How to make a katana out of paper. All you'll need is some durable printer paper or origami paper, double-sided photo album squares, quick drying craft glue, a small craft knife (like an x-acto knife), a straight edge and a cutting mat. 4 years ago, 5 years ago A sturdy ruler to compact folds and smooth out paper5. 5 months ago You can use origami paper that’s 10 inches by 10 inches (25cm by 25 cm). Cut it out.13. Smother it with glue.14. Place the sword along the fold made in the previous step, and trace out the shape of the tip onto the piece.11. 9. Take a piece of paper and cover one side of it with glue, making sure the edges are all covered.2. The second layer of pop sticks should overlap the joins in the previous layer, like the paper blanks. 5. Using the same technique of making the paper blanks, but instead of using three layers only use one. All the way up the blade, place pop sticks 2 wide along the back edge, and right at the tip 1 wide.3,4&5. Position it on the sword and smooth it out. Place over the tip, and work out the shape you need to cut it. Side view of the sword core. Glue sticks (I used 3 and a bit by the time I was finished )3. Take a piece of paper and cover one side of it with glue, making sure the edges are all covered. Cut as shown in the picture. Open it back up, and cover half of the inside with glue, then fold it back together.6. Want to master Microsoft Excel and take your work-from-home job prospects to the next level? 1 & 2. Make your own tiny katana out of paper! DIY - YouTube My inspiration for this instructable comes from Returacan. Open it back up, and cover half of the inside with glue, then fold it back together.9. Continue on with 2 more full blanks, and finish it off with one of the half blanks. Fold in half again and glue.9. Smother it in glue. Place the other piece on top of the glue.9. Use the ruler to smooth out the paper, and to further squish it together.8. Smother the sword core in glue, then place the pop sticks three wide on the handle.2. Use the ruler to smooth out the paper, and to further squish it together.4. Repeat this for the second diagonal. Slide it down the blade and sit it against the top of the hilt. Take 2 of the paper "blanks" and cut them in half horizontally.2. Using some of his methods, I've produced a way to make a sword much quicker and with fewer, slightly more common supplies. Make a tiny Japanese katana or ninja sword out of paper. (Don't forget to use plenty of glue). Continue on with the rest of the blanks layering them as before so you end up with a 4 layer thick sword core.8. on Introduction. Step 2: Paper "Blanks". Fold in half vertically, open up, then smother the entire inside of the piece of laminated paper.2&3. Congratulations you now have a paper sword. It is best to use a flat surface when … Take 2 of the paper "blanks" and cut them in half horizontally. Fold and glue a piece if paper in half horizontally.7. Repeat steps 1 through to 9 until you have 16 paper "blanks". Place on the back of the sword blade and smooth over, bonding it to the reinforced sword blank.4. Ninja Weapon. Something to cut on so you don't destroy your table6. Participated in the Full Spectrum Laser Contest. Laminate 2 pieces of paper together, then fold and glue in half vertically.1. Do this for the whole blade, stopping at the base of the curve of the point. 10. Crease a square of paper on both diagonals. Place one square of professional origami paper in front of you. And if you like it, don't forget to vote for it in the paper craft contest. - YouTube Do this for the whole blade and hilt, stopping just before the bend at the tip of the sword.5. 11. an Instructable on How to Carve a Pumpkin That Replicates the Look of a Shaded Drawing. 1. Fold in half again, and repeat the glueing and ruler squishing.Repeat steps 1 through 6 so you have 27.

.

Sunrise Mountain High School Las Vegas, Red Sea Skimmer Review, Porsche Cayman For Sale Canada, Wagon R 2009 Model, Where To Buy Spaghetti Squash Seeds,